Unlabelled How To Flashing yu yureka plus yu5510a

Wednesday, July 12, 2017

How To Flashing yu yureka plus yu5510a

    No comments


keyword : How To Flashing yu yureka plus yu5510a for bootloop , How To Flashing yu yureka plus yu5510a for softbrick , How To Flashing yu yureka plus yu5510a for hardbrick , How To Flashing yu yureka plus yu5510a Error Camera , How To Flashing yu yureka plus yu5510a blank screen , How To Flashing yu yureka plus yu5510a lost password , How To Flashing yu yureka plus yu5510a stuck logo , How To Flashing yu yureka plus yu5510a new 2017. How To Flashing yu yureka plus yu5510a repair phone.




Download one of the above file:


Further to the next stage
1. Copy the file to Sd Card
2.boot into recovery mode, in the file already exists in the form of .pdf open a full tutorial and follow the instructions. anyone using flashing software.
3. When've followed all of the conditions please check the phone has been normal what is not.
4.Ciri EMMC feature of flashing not damaged in the road, still can wipe data cache. but install the update form sd card can not or will not runing.
5.booting first after install rom fair amount of time of approximately 15 minutes. Do not hurry to remove the battery. wait until the system finishes booting.

important: before doing anything on the phone to do the data backup beforehand. can pass CMW, recovery, twrp please find if you have not got.

How To Flashing yu yureka plus yu5510a

if your yu yureka is stucked at yu logo then keep watching this video. so hey guys, it's jay kapoor here and in this video i'm going to show you how you can unbrick your yu yureka from a soft brick. yes, there are two types of brick. one is the soft brick and another one is hard brick. soft brick occurs when you flash a wrong recovery, file or you are messed up with your system. soft brick can be fixed easily whereas there is no solution for the hard brick. if you have hard brick your phone, your phone will not turn on even if it has battery. your phone will not even boot into the fastboot mode. so the only solution for the hard brick is to go to the service center. and yes, they will fix it for free. so let's come back to the point. how to fix the soft brick issue.

so first of all you have to download a zip file from the link down below in the description. now download the adb setup and fastboot drivers from the link down below in the description, the second link. right click on the adb setup, run as admin, then click on yes. now install the adb drivers, just type 'y' and hit enter. type 'y' and hit enter and it will install the adb and fastboot drivers. now once it installed, let's boot our yureka into the fastboot mode. to do this, take out your phone battery, insert it again. press the volume up button for like 3 seconds and connect the yureka to the pc via the usb cable. once it connected, on the phone screen you will see fastboot mode. now extract the folder that we downloaded earlier, extract it. now there will be a flash bat file. just double click on that and click on run and it will flash the recovery. if it's not flashing for any reason, you can right click on that and click on run as admin.

once the recovery is flashed. you can disconnect the phone. now take out your phone battery again, insert it again. now press vol up + vol down + power button at the same time. you will be in the stock cm recovery. now from the stock recovery, select wipe data/factory reset. and once it's resetted, click on reboot system now and your yureka should work fine. so that's it for now guys. hope your yureka is running fine now. please subscribe to the channel for more helpful videos and you can also click on the like button to show your support. if you have any questions, feel free to leave them in the comment section below. and

No comments :

Post a Comment

Subscribe to: Post Comments ( Atom )